/*
 * Copyright (c) 2015, Freescale Semiconductor, Inc.
 * Copyright 2016 - 2017 NXP
 * All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */
#ifndef __USB_PHY_H__
#define __USB_PHY_H__

/*******************************************************************************
 * Definitions
 ******************************************************************************/
typedef struct _usb_phy_config_struct
{
    uint8_t D_CAL;     /* Decode to trim the nominal 17.78mA current source */
    uint8_t TXCAL45DP; /* Decode to trim the nominal 45-Ohm series termination resistance to the USB_DP output pin */
    uint8_t TXCAL45DM; /* Decode to trim the nominal 45-Ohm series termination resistance to the USB_DM output pin */
} usb_phy_config_struct_t;

#if defined(__cplusplus)
extern "C" {
#endif

/*******************************************************************************
 * API
 ******************************************************************************/
/*!
 * @brief EHCI PHY get USB phy bass address.
 *
 * This function is used to get USB phy bass address.
 *
 * @param[in] controllerId    EHCI controller ID; See the #usb_controller_index_t.
 *
 * @retval USB phy bass address.
 */
extern void *USB_EhciPhyGetBase(uint8_t controllerId);

/*!
 * @brief EHCI PHY initialization.
 *
 * This function initializes the EHCI PHY IP.
 *
 * @param[in] controllerId    EHCI controller ID; See the #usb_controller_index_t.
 * @param[in] freq            The external input clock.
 *
 * @retval kStatus_USB_Success      Cancel successfully.
 * @retval kStatus_USB_Error        The freq value is incorrect.
 */
extern uint32_t USB_EhciPhyInit(uint8_t controllerId, uint32_t freq, usb_phy_config_struct_t *phyConfig);

/*!
 * @brief ehci phy initialization for suspend and resume.
 *
 * This function initialize ehci phy IP for suspend and resume.
 *
 * @param[in] controllerId   ehci controller id, please reference to #usb_controller_index_t.
 * @param[in] freq            the external input clock.
 *                            for example: if the external input clock is 16M, the parameter freq should be 16000000.
 *
 * @retval kStatus_USB_Success      cancel successfully.
 * @retval kStatus_USB_Error        the freq value is incorrect.
 */
extern uint32_t USB_EhciLowPowerPhyInit(uint8_t controllerId, uint32_t freq, usb_phy_config_struct_t *phyConfig);

/*!
 * @brief EHCI PHY deinitialization.
 *
 * This function deinitializes the EHCI PHY IP.
 *
 * @param[in] controllerId   EHCI controller ID; See #usb_controller_index_t.
 */
extern void USB_EhciPhyDeinit(uint8_t controllerId);

/*!
 * @brief EHCI PHY disconnect detection enable or disable.
 *
 * This function enable/disable the host EHCI disconnect detection.
 *
 * @param[in] controllerId   EHCI controller ID; See #usb_controller_index_t.
 * @param[in] enable
 *            1U - enable;
 *            0U - disable;
 */
extern void USB_EhcihostPhyDisconnectDetectCmd(uint8_t controllerId, uint8_t enable);
#if ((defined FSL_FEATURE_SOC_USBPHY_COUNT) && (FSL_FEATURE_SOC_USBPHY_COUNT > 0U))
#if ((defined FSL_FEATURE_USBHSD_HAS_EXIT_HS_ISSUE) && (FSL_FEATURE_USBHSD_HAS_EXIT_HS_ISSUE > 0U))
/*!
 * @brief Force the PHY enter FS Mode
 *
 * on RT500 and RT600, the device doesn't enter FS Mode after vbus is invalide and the controller works as HS.
 *
 * @param[in] controllerId   EHCI controller ID; See #usb_controller_index_t.
 * @param[in] enable
 *            1U - enable;
 *            0U - disable;
 */
extern void USB_PhyDeviceForceEnterFSMode(uint8_t controllerId, uint8_t enable);
#endif
#endif
#if defined(__cplusplus)
}
#endif

#endif /* __USB_PHY_H__ */