/*
 * Copyright 2019 NXP
 * All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

/***********************************************************************************************************************
 * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
 * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
 **********************************************************************************************************************/
/*
 * How to setup clock using clock driver functions:
 *
 * 1. Call CLOCK_InitXXX() to configure corresponding SCG clock source.
 *    Note: The clock could not be set when it is being used as system clock.
 *    In default out of reset, the CPU is clocked from FIRC(IRC48M),
 *    so before setting FIRC, change to use another avaliable clock source.
 *
 * 2. Call CLOCK_SetXtal0Freq() to set XTAL0 frequency based on board settings.
 *
 * 3. Call CLOCK_SetXxxModeSysClkConfig() to set SCG mode for Xxx run mode.
 *    Wait until the system clock source is changed to target source.
 *
 * 4. If power mode change is needed, call SMC_SetPowerModeProtection() to allow
 *    corresponding power mode and SMC_SetPowerModeXxx() to change to Xxx mode.
 *    Supported run mode and clock restrictions could be found in Reference Manual.
 */

/* clang-format off */
/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
!!GlobalInfo
product: Clocks v6.0
processor: MKE16Z64xxx4
mcu_data: ksdk2_0
processor_version: 0.0.6
 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
/* clang-format on */

#include "clock_config.h"

/*******************************************************************************
 * Definitions
 ******************************************************************************/
#define SCG_LPFLL_DISABLE 0U /*!< LPFLL clock disabled */
#define SCG_SOSC_DISABLE  0U /*!< System OSC disabled */

/*******************************************************************************
 * Variables
 ******************************************************************************/
/* System clock frequency. */
extern uint32_t SystemCoreClock;

/*******************************************************************************
 * Code
 ******************************************************************************/
/*FUNCTION**********************************************************************
 *
 * Function Name : CLOCK_CONFIG_FircSafeConfig
 * Description   : This function is used to safely configure FIRC clock.
 *                 In default out of reset, the CPU is clocked from FIRC(IRC48M).
 *                 Before setting FIRC, change to use SIRC as system clock,
 *                 then configure FIRC. After FIRC is set, change back to use FIRC
 *                 in case SIRC need to be configured.
 * Param fircConfig  : FIRC configuration.
 *
 *END**************************************************************************/
static void CLOCK_CONFIG_FircSafeConfig(const scg_firc_config_t *fircConfig)
{
    scg_sys_clk_config_t curConfig;
    const scg_sirc_config_t scgSircConfig = {
        .enableMode = kSCG_SircEnable, .div2 = kSCG_AsyncClkDivBy2, .range = kSCG_SircRangeHigh};
    scg_sys_clk_config_t sysClkSafeConfigSource = {
        .divSlow = kSCG_SysClkDivBy4, /* Slow clock divider */
        .divCore = kSCG_SysClkDivBy1, /* Core clock divider */
        .src     = kSCG_SysClkSrcSirc /* System clock source */
    };
    /* Init Sirc. */
    CLOCK_InitSirc(&scgSircConfig);
    /* Change to use SIRC as system clock source to prepare to change FIRCCFG register. */
    CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource);
    /* Wait for clock source switch finished. */
    do
    {
        CLOCK_GetCurSysClkConfig(&curConfig);
    } while (curConfig.src != sysClkSafeConfigSource.src);

    /* Init Firc. */
    CLOCK_InitFirc(fircConfig);
    /* Change back to use FIRC as system clock source in order to configure SIRC if needed. */
    sysClkSafeConfigSource.src = kSCG_SysClkSrcFirc;
    CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource);
    /* Wait for clock source switch finished. */
    do
    {
        CLOCK_GetCurSysClkConfig(&curConfig);
    } while (curConfig.src != sysClkSafeConfigSource.src);
}

/*******************************************************************************
 ************************ BOARD_InitBootClocks function ************************
 ******************************************************************************/
void BOARD_InitBootClocks(void)
{
    BOARD_BootClockRUN();
}

/*******************************************************************************
 ********************** Configuration BOARD_BootClockRUN ***********************
 ******************************************************************************/
/* clang-format off */
/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
!!Configuration
name: BOARD_BootClockRUN
called_from_default_init: true
outputs:
- {id: Bus_clock.outFreq, value: 24 MHz}
- {id: Core_clock.outFreq, value: 48 MHz}
- {id: Flash_clock.outFreq, value: 24 MHz}
- {id: LPO1KCLK.outFreq, value: 1 kHz}
- {id: LPO_clock.outFreq, value: 128 kHz}
- {id: SIRC_CLK.outFreq, value: 8 MHz}
- {id: System_clock.outFreq, value: 48 MHz}
 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
/* clang-format on */

/*******************************************************************************
 * Variables for BOARD_BootClockRUN configuration
 ******************************************************************************/
const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockRUN = {
    .divSlow = kSCG_SysClkDivBy2,  /* Slow Clock Divider: divided by 2 */
    .divCore = kSCG_SysClkDivBy1,  /* Core Clock Divider: divided by 1 */
    .src     = kSCG_SysClkSrcFirc, /* Fast IRC is selected as System Clock Source */
};
const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockRUN = {
    .freq        = 0U,                        /* System Oscillator frequency: 0Hz */
    .enableMode  = SCG_SOSC_DISABLE,          /* System OSC disabled */
    .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */
    .div2        = kSCG_AsyncClkDisable,      /* System OSC Clock Divider 2: Clock output is disabled */
    .workMode    = kSCG_SysOscModeExt,        /* Use external clock */
};
const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockRUN = {
    .enableMode = kSCG_SircEnable | kSCG_SircEnableInLowPower, /* Enable SIRC clock, Enable SIRC in low power mode */
    .div2       = kSCG_AsyncClkDisable,                        /* Slow IRC Clock Divider 2: Clock output is disabled */
    .range      = kSCG_SircRangeHigh,                          /* Slow IRC high range clock (8 MHz) */
};
const scg_firc_config_t g_scgFircConfig_BOARD_BootClockRUN = {
    .enableMode = kSCG_FircEnable,      /* Enable FIRC clock */
    .div2       = kSCG_AsyncClkDisable, /* Fast IRC Clock Divider 2: Clock output is disabled */
    .range      = kSCG_FircRange48M,    /* Fast IRC is trimmed to 48MHz */
    .trimConfig = NULL,                 /* Fast IRC Trim disabled */
};
const scg_lpfll_config_t g_scgLpFllConfig_BOARD_BootClockRUN = {
    .enableMode = SCG_LPFLL_DISABLE,    /* LPFLL clock disabled */
    .div2       = kSCG_AsyncClkDisable, /* Low Power FLL Clock Divider 2: Clock output is disabled */
    .range      = kSCG_LpFllRange48M,   /* LPFLL is trimmed to 48MHz */
    .trimConfig = NULL,
};
/*******************************************************************************
 * Code for BOARD_BootClockRUN configuration
 ******************************************************************************/
void BOARD_BootClockRUN(void)
{
    scg_sys_clk_config_t curConfig;

    /* Init FIRC. */
    CLOCK_CONFIG_FircSafeConfig(&g_scgFircConfig_BOARD_BootClockRUN);
    /* Init SIRC. */
    CLOCK_InitSirc(&g_scgSircConfig_BOARD_BootClockRUN);
    /* Set SCG to FIRC mode. */
    CLOCK_SetRunModeSysClkConfig(&g_sysClkConfig_BOARD_BootClockRUN);
    /* Wait for clock source switch finished. */
    do
    {
        CLOCK_GetCurSysClkConfig(&curConfig);
    } while (curConfig.src != g_sysClkConfig_BOARD_BootClockRUN.src);
    /* Set SystemCoreClock variable. */
    SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK;
}